New Rochelle Premium Roofing provides professional metal roofing and soldered pans in New Rochelle, NY for residential and commercial properties across Westchester County. Metal roofing in New Rochelle is usually forty square feet, not four thousand. The metal on these houses lives on porch roofs, bay window tops, dormer cheeks and the low-slope connectors between wings, and that is where most of our sheet work happens.
Those small areas are almost always flat-lock pans, soldered at every seam because the pitch is far too shallow for a lapped joint to shed reliably. Done properly they last as long as the slate above them and outlast anything else on the building. Done as a lapped standing seam with sealant in the joint, they fail at the first hard freeze and take the plaster ceiling below with them.
We fabricate in twenty-ounce cold-rolled copper, in lead-coated copper where the runoff would stain masonry or where a green patina would fight the building, and in terne-coated stainless on bay roofs that sit under trees and take constant tannin. Fasteners are concealed cleats, never a face screw with a rubber washer that has to be revisited every decade. Every pan is fabricated on site to the actual opening rather than ordered to a drawing.
Whole-house standing seam does have a place here, mostly on postwar colonials with simple gable geometry and on rear additions. On a pre-war house with six dormers, three chimneys and a turret, the panel count and the flashing complexity push the price past a slate relay while delivering a shorter service life, and we will show you that arithmetic on paper rather than quoting around it. The comparison is worth seeing before you commit to either.
We do not install exposed-fastener corrugated or ribbed panel on residential roofs in this market. It is a good agricultural and light-industrial product and a poor fit for a Westchester street, and the fastener gaskets become a recurring maintenance item long before the panel itself is anywhere near worn out. There are better places to spend the same money on a house like this.
Repairs to existing metal are done with heat and solder, not with tape or a tube. Pinholed pans get patched or replaced, open lock seams are re-tinned and re-soldered, and where a pan has to come out from under slate, the courses above are lifted with rippers and re-hung on hooks rather than broken to save an hour of labor. Tape on a soldered pan is a temporary measure that becomes permanent through neglect.
Our licensed and insured team brings the right materials and equipment to every job — lead-coated copper step and pan flashing, twenty-ounce cold-rolled copper valley linings, slate rippers and copper bib repairs, stainless slate hooks set at the head lap, semi-weathering gray and unfading green roofing slate, terne-coated stainless bay-roof pans — and backs the work with a written workmanship warranty. We serve New Rochelle and nearby communities including Larchmont, Mamaroneck, Pelham, Pelham Manor.
What We Handle
Everything our metal roofing and soldered pans in New Rochelle covers
One crew, one point of contact, and the full range of metal roofing and soldered pans work in New Rochelle, NY. If it is on this list we do it in house rather than handing it to a subcontractor:
- metal roofing new rochelle
- metal roofing
- standing seam roof westchester
- copper bay roof
- soldered flat lock pans
- porch roof metal replacement
- terne coated stainless roofing
- copper roofing new rochelle
- metal roof cost ny
- dormer cheek metal
- low slope metal connector
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our New Rochelle services.
Materials, equipment and how we do metal roofing and soldered pans
The difference between metal roofing and soldered pans that lasts and metal roofing and soldered pans that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with lead-coated copper step and pan flashing, twenty-ounce cold-rolled copper valley linings, slate rippers and copper bib repairs, stainless slate hooks set at the head lap, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every New Rochelle job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. Years of roofing work in Westchester County means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do metal roofing and soldered pans outside New Rochelle
New Rochelle Premium Roofing covers New Rochelle and the surrounding communities of Westchester County. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Metal Roofing and Soldered Pans in Larchmont, NY — Westchester County, population 6,630
- Metal Roofing and Soldered Pans in Mamaroneck, NY — Westchester County, population 20,151
- Metal Roofing and Soldered Pans in Pelham, NY — Westchester County, population 7,326
- Metal Roofing and Soldered Pans in Pelham Manor, NY — Westchester County, population 5,752
- Metal Roofing and Soldered Pans in Scarsdale, NY — Westchester County, population 18,253
- Metal Roofing and Soldered Pans in Eastchester, NY — Westchester County, population 20,901
Start on the New Rochelle Premium Roofing homepage for a free estimate, or call (844) 511-2320 and describe the job.
Why New Rochelle Chooses New Rochelle Premium Roofing
- ✓We give the covering, the flashing metal and the fasteners three separate remaining-life numbers, because on a Westchester roof they almost never run out together
- ✓Slate relay and full replacement are quoted as two priced lines, with the expected breakage percentage written down before anyone climbs
- ✓We will not coat slate, clay tile or an asphalt shingle roof, and we will explain on site what a coating does to the salvage value
- ✓Every slate we lift comes off with a ripper and goes back on a copper nail or a stainless hook, never face-nailed through the exposure
The standards behind metal roofing and soldered pans
Quality here is not a matter of opinion — it is written down. The metal roofing and soldered pans work we do in New Rochelle follows published industry standards: NRCA publishes the Roofing Manual, the industry's reference for details and slope minimums, and Asphalt Roofing Manufacturers Association sets the shingle application and ventilation guidance the warranties reference. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every metal roofing and soldered pans project in New Rochelle gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 511-2320 for a free metal roofing and soldered pans free estimate in New Rochelle, or request a quote and we'll get right back to you.